Gunner’s Journal

The 1911 Worlds Finest Handgun!

Posts Tagged ‘Upgrades Hi Power’

Daly Hi Power Completed Upgrades

Posted by Gunner on May 9, 2008


Charles Daly HP with Novak Sights and Craig Spegal Grips


This is my Daly Hi Power after the upgrades.

  I added several upgrades to my Daly Hi Power. These are actually fewer additions than if it had been a Browning since the Daly has the proper slide cuts for easy addition of Novak sights.


Craig Spegal Custom Grips From Novak. These are the grips on the Daly.
Beautiful Work!

  I added these Spegal grips as well as a set of  Novak plain black sights to replace the XS sights. The other Daly will keep the XS sights. I wanted the Novaks on this one to be more precise in my shooting when on the range. The later model Daly HP’s use a standard 1911 Novak slide cut which certainly makes it easy to change these sights out. The folks at XS told me they didn’t want a proprietary slide cut so owners wouldn’t be limited to the XS sights. They decided that the Novak cut for the 1911 was the best possible solution sense these are the most prolific sights on the market. My hats off to them for this decision! Novak only charges $59 plus shipping for these sights. The grips were $75 and graded Std+.
 Installing these sights was a very simple task and took about 30 minutes with only very minor fitting on the front sight with none on the rear. The rear Novak sight was an appropriately snug fit that only needed a tightening of the set screw on top of the sight. The front sight needed a few light passes with 1200 grit wet dry sandpaper to fit properly. After that it was just a simple matter to sight the pistol in. Using the plain black sights allows a very good sight picture with ample space on either side of the front sight.
  The Spegal grips fit like a glove as expected but did come with detailed instructions for fitting should yours need it.


Novak Sight Selections

 Along with these last additions there was also the addition of the Cylinder and Slide trigger, reduced tactical spring kit which included the extra power trigger return spring, mainspring, extra power firing pin spring and the addition of a C&S sear spring. With the exception of an extractor spring and new extractor most all the internals are now from C&S. This makes for a wonderful trigger, reliability and no MIM parts. The only other addition will be a Bar-Sto match barrel in a couple of months. It’s very accurate as is and this will make it a tac driver for certain.
 The sight used is pictured above as the top left and also pictured on the bottom right. The product codes are as follows. LMC01 Colt plain black, DFS02-3.225 black front. These are the standard Novak slide cuts for the 1911. Now this is for the later model Daly HP’s finished by Magnum Research. The earlier guns finished by Dan Wesson used a standard Novak cut for the series II Hi Power. Check my original review for the serial number reference to make sure you order the correct sights for your gun.
 Even though the high quality parts added a good amount to the Daly project it came out very nice. Of course if you choose to do the same with your Browning you will need to send your slide in to Novak to have the slide cut for the sights. Turnaround time is one week or less depending on your location and mailing time. One other thing I have to commend Novak on besides the usual great customer service is the shipping time and cost. Many companies add to the profit for parts etc. by charging high shipping cost. Novak will not do that. Two Day Air shipping from UPS was only an $8.00 charge from Novak. Now that’s very reasonable!
I hope you enjoyed the review on my mods to this pistol and will find it useful.

Blogged with the Flock Browser

Tags: , , ,

Posted in Charles Daly Hi Power, Hi Powers | Tagged: , , | 10 Comments »